EAA/EGA High Efficiency Wall Mount Air Conditioners

Eubank EAA/EGA Wall Mount Air Conditioner

Used primarily to cool telecommunication equipment shelters, Eubank® vertical package exterior wall mount air conditioners are problem solvers for a wide range of conditions and applications. Due to the high internal heat load, these shelters require cooling even when outside temperatures drop below 60°F (15°C). The Eubank family of exterior wall mount air conditioners have the necessary controls and components for operation during these (less than 60°F [15°C]) temperatures. All models use the non-ozone depleting R-410A refrigerant.

Eubank air conditioners are available with an optional factory installed economizer. When ambient conditions are cool and dry, the economizer uses outside air to cool the shelter. The economizer provides temperature control, energy cost savings, and increased reliability by decreasing the operating hours of the compressor and the condenser fan. All economizers are factory installed and tested. In addition, factory and field installed options and accessories can be used to meet specific requirements.

EAA1020A - EAA1060A & EGA1072A Exterior Wall Mount Air Conditioner

These models are our most popular air conditioners used in a variety of applications including telecommunications shelters, classrooms, relocatable offices and control rooms. All models are suitable for operation up to 120ºF and are available with Desert Duty Extreme Duty packages.

The Desert Duty Package allows operation up to 131ºF (55ºC).

The Extreme Duty Package allows operation from 0ºF to 131ºF (-18ºC to 55ºC) for economizer equipped models and -40ºF to 131ºF (-40ºC to 55ºC) for models with an economizer.

➤ EAA High Efficiency Models

  • EER: 11.00 - 11.50
  • Cooling Capacities: 1.5, 2, 2.5, 3, 3.5, 4 and 5 tons (20,000 BTUH to 60,000 BTUH)
➤ EGA High Efficiency Models

  • EER: 10.0
  • Cooling Capacities: 6 tons (72,000 BTUH)

Download Product Literature

Contact Eubank Sales:

Toll Free: (800) 726-2734


Designed for Operation in Low Ambient Conditions

  • Low ambient control cycles condenser fan to maintain proper refrigerant pressures. Allows operation in mechanical cooling (compressor) of our standard air conditioners down to 20°F (-7°C). With the Extreme Duty option, the units will operate down to 0°F (-18°C). Note: low temperature operation is affected by ambient conditions, e.g. wind and humidity.
  • Three minute by-pass of the low pressure switch for start-up of compressor when outdoor temperatures are below 55°F (13°C).
  • Optional Factory built-in economizer.

High Efficiency

  • High efficiency compressor.
  • Lanced fins standard on all evaporator and condenser coils.

Built-in Reliability

  • High pressure switch and low pressure switch with lockout protects refrigerant circuit.
  • Adjustable .03 to ten minute delay on make for short cycle protection.

    Remote Alarm Capability

    • Dry contacts can be used for remote alarm or notification upon air conditioner lockout.

    Ease of Service

    • Service access valves are standard.
    • Standard 2” (50 mm) pleated filter with a MERV rating of 8 changeable from outside.
    • All major components are readily accessible.
    • Front Control Panel allows easy access and complies with NEC clearance codes on redundant side-by-side systems.
    • LEDs indicate operational status and fault conditions.
    • Foil backed insulation on the indoor air path.
    • A minimum position potentiometer that can be adjusted to prevent the economizer damper from closing completely. This control ensures that whenever the evaporator fan is operating, fresh air is being introduced into the building.

      Rugged Construction

      • Copper tube, aluminum fin evaporator & condenser coils.
      • Field or factory installed heaters on discharge side of evaporator coil (optional)
      • Baked on neutral beige finish over galvanneal steel for maximum cabinet life. (Other finishes are available.)

      Ease of Installation

      • Sloped top with flashing eliminates need of rainhood.
      • Built-in mounting flanges facilitate installation and minimize chance of water leaks.
      • Supply and return openings exactly match previous models.
      • Factory installed disconnect on all units.
      • Single Point Power Entry complies with latest edition of U.L. Standard 1995.
      • Side access panels for easy access to electrical connections.